ABSTRACT
OBJECTIVE@#To prepare customized porous silicone orbital implants using embedded 3D printing and assess the effect of surface modification on the properties of the implants.@*METHODS@#The transparency, fluidity and rheological properties of the supporting media were tested to determine the optimal printing parameters of silicone. The morphological changes of silicone after modification were analyzed by scanning electron microscopy, and the hydrophilicity and hydrophobicity of silicone surface were evaluated by measuring the water contact angle. The compression modulus of porous silicone was measured using compression test. Porcine aortic endothelial cells (PAOECs) were co-cultured with porous silicone scaffolds for 1, 3 and 5 days to test the biocompatibility of silicone. The local inflammatory response to subcutaneous porous silicone implants was evaluated in rats.@*RESULTS@#The optimal printing parameters of silicone orbital implants were determined as the following: supporting medium 4% (mass ratio), printing pressure 1.0 bar and printing speed 6 mm/s. Scanning electron microscopy showed that the silicone surface was successfully modified with polydopamine and collagen, which significantly improved hydrophilicity of the silicone surface (P < 0.05) without causing significant changes in the compression modulus (P > 0.05). The modified porous silicone scaffold had no obvious cytotoxicity and obviously promoted adhesion and proliferation of PAOECs (P < 0.05). In rats bearing the subcutaneous implants, no obvious inflammation was observed in the local tissue.@*CONCLUSION@#Poprous silicone orbital implants with uniform pores can be prepared using embedded 3D printing technology, and surface modification obviously improves hydrophilicity and biocompatibility of the silicone implants for potential clinical application.
Subject(s)
Animals , Rats , Swine , Silicon , Orbital Implants , Endothelial Cells , Porosity , Silicones , Printing, Three-DimensionalABSTRACT
Objective:To investigate the effect of free thenar perforator flap on repair of finger pulp defect.Methods:From September 2019 to November 2021, 79 cases of finger injuries complicated with defects in the pulp of fingers received free thenar perforator flap transfer surgery for reconstruction of finger pulps in the Department of Hand and Foot Surgery, Taizhou Hospital, Zhejiang Province. The patients were 51 males and 28 females, aged from 17 to 52(37.5±5.2) years old. There were 34 finger-pulp defects of index fingers, 15 of middle fingers, 26 of ring fingers and 4 of little fingers. All patients were treated with free thenar perforator flaps sized 2.0 cm×2.5 cm-3.0 cm×3.5 cm. All thenar perforator flaps were pedicled with the perforator artery and subcutaneous superficial vein in the thenar region, and the vessels were anastomosed with the proper palmar digital artery and dorsal digital vein, respectively. At the same time, subcutaneous nerve and proper palmar digital nerve were sutured to reconstruct the sensation of flaps. During the operation, the dominant perforating branch of thenar was found being originated from the superficial palmar branch of radial artery in 27 cases, from the superficial palmar arch in 21 cases, from the perforating branch of metacarpophalangeal proper artery of thumb in 11 cases, from the radial artery in 10 cases and from the main artery of thumb in 10 cases. The origins of nerves within the flaps were found from the superficial branch of radial nerve(24 cases), the terminal branch of lateral cutaneous nerve of forearm(22 cases) and the palmar branch of median nerve(33 cases). The operation time was (96.7±10.7) minutes. The donor site for the flap was closed directly without skin grafting. Most of the follow-up were conducted through the visit of outpatient clinic and the patients from other regions were reviewed via telephone or WeChat.Results:All perforator flaps survived completely and the flap donor sites healed smoothly. Follow-up lasted for (20.5±3.8) months. The reconstructed finger pulp was not bulky and the texture was satisfactory. TPD of the flaps was (5.6±0.9) mm. Only a linear scar left in the flap donor sites without significant affect on thenar function.Conclusion:The vascular anatomy of thenar perforator flap is constant, which helps to regain sensations of the flap. The texture and thickness of the flap are similar to those of the finger. It is ideal for reconstruction of defect of finger pulp.
ABSTRACT
3D bioprinting is an advanced manufacturing technology that utilizes biomaterials and bioactive components to manufacture artificial tissues and organs. It has been widely applied in multiple medical fields and possesses outstanding advantages in organ reconstruction. In recent years, 3D bioprinted organs have made an array of groundbreaking achievements. Nevertheless, it is still in the exploratory stage of research and development and still has bottleneck problems, which can not be applied in organ transplantation in vivo. In this article, the application of 3D printing technology in medicine, characteristics of 3D bioprinting technology, research hotspots and difficulties in bionic structure, functional reconstruction and immune response of 3D bioprinted organs, and the latest research progress on 3D bioprinting technology were illustrated, and the application prospect of 3D bioprinting technology in the field of organ reconstruction was elucidated, aiming to provide novel ideas for the research and clinical application of organ reconstruction and artificial organ reconstruction, and promote the development of organ transplantation and individualized medicine.
ABSTRACT
Objective:To use three-dimensional (3D) scanning to measure the preoperative and postoperative nasal parameters of the patients received rhinoplasty with ear cartilage and silicone prosthesis, and to evaluate the clinical effect of the surgery.Methods:Sixteen female patients with an average age of 28.3 years, ranged from 21 to 35 years, received rhinoplasty with ear cartilage and silicone prosthesis in Wuhan Tongji Hospital from June 2018 to February 2019. Preoperative and postoperative 3D scanning was performed to measure nasal parameters, including linear length, angle, and proportional index.Results:All patients were satisfied with the postoperative outcomes. The postoperative nasal length, nasal height, and nasal depth increased significantly, and the postoperative nasal width and nasal tip width decreased. The postoperative nasolabial angle and nasofrontal angle were statistically improved, while the preoperative and postoperative data of columellar facial angle, nasal tip angle, and nasal column-lobular angle were not significantly different. The ratios of nasal depth and nasal width, nasal index and nasal tip protrusion were improved after surgery, while the postoperative ratios of nasal columella and nasal lobules length were not statistically improved.Conclusions:The 3D scanning allows for comprehensive and accurate measurement of the nasal parameters. The rhinoplasty with ear cartilage and silicone prosthesis is more effective in improving the overall contour of the nose, but less effective in improving the aesthetics of the nasal tip.
ABSTRACT
OBJECTIVE： To prepare β-sitosterol （shorted fo r “Sit”） and its deri vatives from the fruit of Sorbus pohuashanensis，and to investigte their antidepressant activities. METHODS ：Using the fruit of S. pohuashanensis as raw material ， extracted with 75％ ethanol and 20％KOH solution ，Sit was obtained after extraction and crystallization. C 3 hydroxyl group of Sit was used as the structural modification site ，CH2Cl2 was used as the reaction solvent ，DMAP was used as catalyst ，EDCI was used as dehydrating agent ，4 kinds of organic acids （salicylic acid ，2-tetrahydrofuranic acid ，phenylalanine，sorbic acid ）were added to make the carboxylation reaction to produce ester derivatives Sit-S ，Sit-T，Sit-P and Sit-Sr. The chemical structure of its derivatives were elucidated by IR and NMR. The tail suspension test and the forced swimming model were used to preliminarily explore the antidepressant active components of Sit and 4 kinds of derivatives ；tail suspension test and the spontaneous exercise capacity test were used to screen effective dose of the compounds with antidepressant active. The compound was used alone or in combination with agomelatin [ 40 mg/kg，5-hydroxytryptamine（5-HT）and 5-HT 2C receptor antagonist] ，haloperidol [ 0.2 mg/kg，non-selective D2 receptor antagonist] and bicuculline [ 4 mg/kg，competitive γ-aminobutyric acid（GABA）antagonist]，respectively. Sixty minutes after intraperitoneal injection ，tail suspension test was performed. The levels of 5-HT，dopamine（DA）and GABA in brain tissues of mice were detected by ELISA. The blank control group was given intraperitoneal injection of 10％ propylene glycol solution. RESULTS：By spectrum technology ，the corresponding ester compounds were synthesized by the reaction of Sit with four kinds of organic acids. Among Sit and its four derivatives ，the immobility time of Sit-S group was the shortest in tail suspension test and forced swimming test ，which was significantly shorter than that of blank control group （P＜0.05）. Screening results of Sit-S showed that the effective antidepressant dose was 4 mg/kg， ＊ and it did not affect the spontaneous activity of mice compared with the blank control group （P＞0.05）. With this dose ，Sit-S could significantly shorten the immobility time of mice in tail hua1666@163.com suspension test （P＜0.01），and can s ignificantly increase the ·64levels of 5-HT，DA and GABA in the brain tissue of mice （P＜0.05 or P＜0.01），but its effect can be reversed by agomelatine ， haloperidol and bicuculline to different extent. CONCLUSIONS ：Sit salicylate derivatives Sit-S exhibits good antidepressant activity，and its mechanism of action may be mediated by increasing the levels of 5-HT，DA and GABA.
ABSTRACT
Objective:To investigate the efficacy and safety of three-dimensional navigation template assisted osteotomy for fracture malunion of lateral condyle of humerus in children.Methods:Eighteen children with ma-lunion of fracture of lateral condyle of humerus were treated in Southern Medical University Third Affiliated Hospital from August 2012 to December 2019 and analyzed retrospectively.Among them, 12 cases were treated with routine ope-ration: according to CT reconstruction and empirical osteotomy during the operation, the location of deformity was analyzed.Six cases were treated with navigation template assisted osteotomy: according to the CT data of bilateral elbow joints, a three-dimensional bone model was established, and the coronal and sagittal deformities of the distal humerus were evaluated by comparing the images of the distal humerus of the affected side with the distal humerus of the healthy side, so as to determine the best plane of osteotomy and the target position of reduction.The preoperative simulation was carried out on the computer, and the osteotomy navigation template and reduction navigation template were designed.The navigation template was printed out with a 3D printer.During the operation, the osteotomy was corrected with the assistance of navigation template, and the broken end of osteotomy was fixed with hollow screw and fixed with 80 degree flexion plaster.The X-ray films of the two groups were reexamined regularly after operation.The amount of intraoperative blood loss, operation time, incidence of postoperative complications (necrosis of humeral head and trochlea, delayed ulnar nerve paralysis, and bone nonunion) and the recovery of flexion and the extension function of elbow joint were observed in the 2 groups.Results:The elbow joint activity of all children basically returned to normal, the orthopedic site of osteotomy achieved bony healing, and the orthopedic effects were satisfactory.All the 18 cases were followed up for 6-24 months (mean 15 months). According to the postoperative Dhillon score, the navigation template group was excellent in 1 case and better in 5 cases, while in the routine group, 11 cases were batter and 1 case was fair.There were no significant differences in Dhillon score between the 2 groups after operation ( P>0.05). There were no significant differences in the range of the motion of elbow joint between the 2 groups ( P>0.05). In the comparison of operation time and intraoperative blood loss, the navigation template group [(200.0±24.2) min, (85.0±10.9) mL]was better than the routine group[(232.0±20.1) min, (139.1±18.3) mL](all P<0.001). Conclusions:The application of three-dimensional humerus reconstruction and mirror image contrast to evaluate the distal humerus deformity of the affected side, and the design of osteotomy and reduction navigation template auxiliary operation can restore the normal anatomical structure of elbow joint to the greatest extent.Accurate correction, and the function of elbow joint recover well after operation, which optimizes the operation procedure, improves the safety and effectiveness of the operation.
ABSTRACT
Objective:To optimize the topological design of locking plate for distal radial fracture so that the internal fixation stiffness can be customized.Methods:Models of both the distal radial fracture and the conventional locking plate fixation were constructed using software for three-dimensional modeling and computer-aided design. Based on the data from our previous finite element analysis, a decrease of 33.33% in axial stiffness but retention of more than 90.00% in torsional stiffness were defined as the optimization limits. The conventional plate was redesigned by way of topological optimization iterations. Finite element analysis was done to compare stiffness and interfragmentary strain (IFS) between the new optimized design and conventional design of the locking plate under both compressive and torsional loads.Results:The axial stiffness of the optimized plate was 636.5 N/mm with a downgrading magnitude of 19.7% which was close to the given limit; the torsional stiffness was 634.12 Nmm/° with a downgrading magnitude of 8.8% which remained under the given limit. In the optimized design, a more significant increase was observed in axial IFS than that in shear IFS, leading to a similar effect as the stiffness regulation did.Conclusion:The optimized design of locking plate for distal radial fracture can provide a reliable solution for customized regulation of the internal fixation stiffness.
ABSTRACT
Orthopedic 3D printed surgical navigational template is an instrument that is prepared by 3D reconstruction based on preoperative radiological data of the patient using computer-aided design (CAD) and 3D printing techniques. The 3D printed navigational template allows accurate intra-operative assessment of the relative spatial distance, angular relationship, direction and depth. The application of 3D printed navigational template technique in orthopedics surgeries achieves the conversion of preoperative planning from 2/3D graphics to 3D models, and provides a new method for individualized and precise treatment. Herein we review the evolution, clinical application, and basic classification of 3D printed navigation template technique, analyze its advantages and disadvantages, and discuss the current problems and the future development of this technique.
Subject(s)
Humans , Computer-Aided Design , Orthopedic Procedures , Printing, Three-DimensionalABSTRACT
Objective@#To retrospectively analyze the differential diagnosis and treatment strategy of neonatal intestinal perforation caused by neonatal necrotizing enterocolitis (NEC) and Hirschsprung′s disease (HD).@*Methods@#The clinical data of 42 cases with NEC and 22 cases with HD combined with intestinal perforation from Ja-nuary 2012 to January 2017 admitted at Fujian Provincial Maternity and Children′s Hospital were collected, the proportion of premature infants, and the proportion of low birth weight infants, age of onset, preoperative clinical symptoms and surgical treatment was compared between the two groups.@*Results@#The proportion of premature infants[95.23%(40/42 cases) vs.27.27%(6/22 cases)], the proportion of low birth weight infant[90.48%(38/42 cases) vs.45.45%(10/22 cases)]and the age of onset [(14.48± 10.51) d vs.(3.18±3.43) d]were statistically different between the NEC group and the HD group, and the differences were statistically significant(all P<0.05). There were significant differences in the presence of normal defecation before the operation[71.4% (30/42 cases)vs.27.3%(6/22 cases)], and in the the defecation characteristics at the onset[95.2% (40/42 cases)vs.9.1%(2/22 cases)]between the NEC group and HD group(all P<0.05). Among 42 cases of NEC patients, 8 cases underwent intestinal anastomosis, and 34 cases underwent enterostomy because of the high risk of anastomosis.All of 22 patients with HD underwent double-lumen enterostomy.@*Conclusions@#The general conditions, preoperative manifestations and intraoperative fin-dings of the children should be comprehensively analyzed for identification.Enterostomy is recommended for NEC intestinal perforation, but if the risk of anastomosis is high, then fistula should be performed.Double-lumen fistula should be recommended for HD intestinal perforation, and enterostomy should be recommended if the two cannot be clearly distinguished.
ABSTRACT
Objective To retrospectively analyze the differential diagnosis and treatment strategy of neonatal intestinal perforation caused by neonatal necrotizing enterocolitis (NEC) and Hirschsprung's disease (HD).Methods The clinical data of 42 cases with NEC and 22 cases with HD combined with intestinal perforation from January 2012 to January 2017 admitted at Fujian Provincial Maternity and Children's Hospital were collected,the proportion of premature infants,and the proportion of low birth weight infants,age of onset,preoperative clinical symptoms and surgical treatment was compared between the two groups.Results The proportion of premature infants[95.23％ (40/ 42 cases) vs.27.27％ (6/22 cases)],the proportion of low birth weight infant [90.48％ (38/42 cases) vs.45.45％ (10/22 cases)] and the age of onset [(14.48 ± 10.51) d vs.(3.18 ± 3.43) d] were statistically different between the NEC group and the HD group,and the differences were statistically significant(all P ＜ 0.05).There were significant differences in the presence of normal defecation before the operation [71.4％ (30/42 cases) vs.27.3％ (6/22 cases)],and in the the defecation characteristics at the onset[95.2％ (40/42 cases)vs.9.1％ (2/22 cases)] between the NEC group and HD group(all P ＜ 0.05).Among 42 cases of NEC patients,8 cases underwent intestinal anastomosis,and 34 cases underwent enterostomy because of the high risk of anastomosis.All of 22 patients with HD underwent double-lumen enterostomy.Conclusions The general conditions,preoperative manifestations and intraoperative findings of the children should be comprehensively analyzed for identification.Enterostomy is recommended for NEC intestinal perforation,but if the risk of anastomosis is high,then fistula should be performed.Double-lumen fistula should be recommended for HD intestinal perforation,and enterostomy should be recommended if the two cannot be clearly distinguished.
ABSTRACT
Three-dimensional (3D) printing,a key technique of rapid prototyping (RP),is developing rapidly all over the world.As 3D printing has a significant advantage of personalized manufacturing,it has exerted a profound effect on medicine.The high demand for personalized manufacturing in the field of orthosis provides an excellent opportunity for widespread use of 3D printing technique.This review briefly introduces the principles and characteristics of different forming methods of 3D printing,the types and characteristics of 3D printing materials widely used at present,and classification and clinical application of orthoses.We also summarize the domestic and international research on and manufacture oforthoses using 3D printing techniques,and discuss current problems and future development of 3D printing techniques in orthosis.
ABSTRACT
Objective To investigate whether a 3D printed model of the contrlateral healthy distal radius, especially its articular accuracy, helps anatomical reduction and precise reconstruction of the fractured distal radius. Methods The CT data of bilateral radii were collected from 15 normal volunteers ( 11 males and 4 females with an average age of 22. 8 years ) between November and December 2016. After 3D reconstruction of the bilateral distal 1/3 radii, solid 3D models of left radius were mirrored and generated by 3D printing. The data of right radii ( reference group ) were compared with the data of the solid 3D models of left radius acquired through a 3D scanner ( test group ) using deviation analysis. Results The maximum volume difference between the 3D printed model and the contralateral radius was 6. 86％. The average volume of the reference group was 19, 165. 82 ± 3, 250. 50 mm3 and that of the test group 19, 310. 65 ± 3, 305. 15 mm3, showing no statistically significant difference between the 2 groups ( t= -0. 941, P=0. 363 ) . The maximum surface area difference was 3. 84％ between the 2 groups. The average surface area of the reference group was 5, 075. 80 ± 549. 34 mm2 and that of the test group 5, 139. 43 ± 572. 48 mm2, showing a signifi-cant difference ( t= -2. 451, P=0. 028 ) . The 3D deviation analysis showed a mean positive deviation of 0. 37 ± 0. 10 mm and a mean negative deviation of 0. 30 ± 0. 07 mm. The maximum mean square root was 0. 65. The 3D deviation was distributed mainly within 1 mm interval, with a distribution frequency of 96. 27％. Conclusions A 3D printed model prepared by high precision equipment is accurate enough to guide reconstruction of distal radius fractures in adults. In the treatment of complex fractures of the distal radius, a 3D printed model of the contralateral healthy distal radius can be used as a reference to achieve anatomical reduction and precise reconstruction of the fractured distal radius.
ABSTRACT
Objective To investigate the application of 3D-printing and digital technology in the preoperative design of internal fixation for intra-articular calcaneal fractures.Methods Thin-layer CT images of bilateral calcanei were collected from 12 patients who had been treated for calcaneal fracture of Sanders type Ⅲ from November 2015 to October 2016.They were 7 men and 5 women,aged from 23 to 53 years (average,38.7 years).The images were uploaded into Mimics software for 3D reconstruction,virtual reduction and digital surgical design.Real-size calcaneal models and navigation modules were produced using 3D printing technology for plate preshaping and surgical simulation.The operations were carried out according to preoperative design.The postoperative calcaneal morphological parameters were evaluated.Comparisons were made between postoperative results and preoperative digital design.Results The operating time for the 12 patients ranged from 60 to 90 minutes,averaging 77.9 minutes.Their follow-ups ranged from 4 to 8 months,averaging 6.2 months.No complications affecting their soft tissues happened.The postoperative B(o)hler angle (32.6° ± 3.6°) and Gissane angle (123.9° ± 9.5°) were significantly improved compared with the preoperative values (12.4° ± 2.1° and 143.9° ± 7.8°) (P ＜ 0.001).The shape of postoperative calcaneus was similar to that of the preoperative reduction model.The internal fixation locations and nail directions were in agreement with the preoperative design.Their average Maryland score was 87.8 and excellent to good rate 91.7％.Conclusion This technique can transform a digital design for intra-articular calcanealfracture into real operation tools to help realize a precise surgical design for such fractures.
ABSTRACT
At present, the prevalence rate of diabetes presents a rising tendency. The cardiovascular disease is a major complication of diabetes mellitus and acute coronary syndrome (ACS) is a severe form of coronary heart disease. Compared with non-diabetic patients, the disease situation in diabetic ACS patients is more serious with more contradictory problems and difficulty in treatment. Although percutaneous coronary intervention (PCI) plays a certain role in re-canalization of coronary artery, after PCI the problems the patients with diabetic ACS will face are still serious. traditional Chinese medicine (TCM) recognizes that the etiology and pathogenesis of diabetic ACS are deficiency in Qi and Yin, and accumulation of blood stasis and toxin inside the body. Through clinical observation and retrospective analysis, it is found that using "supplementing Qi and nourishing Yin, activating blood circulation and detoxifying"can interfere with the patients' diabetic ACS and simplify the therapeutic regimen, which is an integrated regulatory treatment with multiple links, multiple pathways and multiple targets, and is a sufficient realization of unique superiority of traditional Chinese medicine by using holistic concept, syndrome differentiation and multiple-link interference for comprehensive prevention and treatment of diabetic ACS.
ABSTRACT
The clinical manifestations and CT findings of 26 patients,who were full-time cooks working in small restaurants,were analyzed retrospectively.The main clinical manifestations were chest congestion,shortness of breath,chest pain,cough and hemoptysis.Lung CT scanning revealed lung carcinoma in 1 case,pulmonary nodules in 16 cases including 2 cancerous nodules confirmed in the followup review,puhnonary bulla in 6 cases,emphysema in 4 cases,fibro-proliferative lesions in 8 cases,interstitial pneumonia in 4 cases and fungal ball in 1 case.Among 26 patients,12 had two or more concurrent intrapulmonary lesions.The results suggest that long-term exposure to cooking oil fume may lead to a series of pulmonary pathological changes,and attention should be paid to the occupational hazards of cooks.
ABSTRACT
Objective To discuss the clinical effect of the phase-one treatment scheme for traumatic osteomyelitis in tibia by combining flap,vancomycin-loaded calcium sulfate and autogenous iliac bone.Methods From January,2009 to July,2014,49 patients which had traumatic osteomyelitis in tibia and met the inclusive criteria were investigated and treated.By taking these patients as treatment group A(34 cases),they were treated by adopting the phase-one treatment scheme of combing tissue flap,vancomycin-loaded calcium sulfate and autogenous iliac bone.Fifteen patients who were treated by using the phase-one treatment scheme,namely,removing the lesion,implanting vancomycin-loaded calcium sulfate and repairing the defect by means of tissue flap,were chosen as control group B.Concerning treatment group A,drainage fluid was collected after operation every day to measure the concentration of vancomycin until drainage tube was removed.All the patients were followed up to study the following indexes:the standing time of drainage tube,the healing time of fracture,infection control rate,bone nonunion rate and other complications.Results All cases were followed up during 17 to 40 months after operation and no amputation was conducted for the affected limb.To repair soft tissue defect,flap and direct suture were adopted for 25 and 9 cases respectively in group A;The results indicated that all flaps survived,the poor healing of flap defect was observed for 2 cases which were healed after dressing change.However,to repair soft tissue defect,all group B cases used flaps;results revealed that distal flap necrosis was found in 2 cases applying neurocutaneous flap,with defect exudation and infection while the 2 cases were cured after debridement and dressing change without performing a second flap operation.In group A,3 cases recurred during 5 months to 2 years after operation;in group B,it was 1;other complications included pintract infection,nonunion,numbness of anterolateral thigh,hematocele in iliac 1 region.In group B,refracture occurred for 2 cases at the original lesion location 18 and 25 months after healing and was cured after plate refixation and the graft of autogenous iliac bone;intraoperative pathology validated no recurrence of osteomyelitis.The standing time of drainage tube was (12.53±4.56) days on average for group A while (17.07±3.87) days for group B;The difference was statistically significant (P＜0.05).The healing time of fracture was (6.20±2.16) months on average for group A while(8.36±2.84) months for group B.The difference was statistically significant(P＜0.05).Conclusion In one stage treatment of localized and diffused traumatic osteomyelitis,the scheme of combining tissue flap,vancomycin-loaded calcium sulfate and autogenous iliac bone effectively shortened the healing time of fracture,increased the healing strength,and reduced the exudation after operation,without increasing infection recurrence rate.The scheme was superior to merely implanting vancomycin-loaded calcium sulfate.
ABSTRACT
Objective To investigate the application of 3D-printing and digital technology in the preoperative design of internal fixation for intra-articular calcaneal fractures.Methods Thin-layer CT images of bilateral calcanei were collected from 12 patients who had been treated for calcaneal fracture of Sanders type Ⅲ from November 2015 to October 2016.They were 7 men and 5 women,aged from 23 to 53 years (average,38.7 years).The images were uploaded into Mimics software for 3D reconstruction,virtual reduction and digital surgical design.Real-size calcaneal models and navigation modules were produced using 3D printing technology for plate preshaping and surgical simulation.The operations were carried out according to preoperative design.The postoperative calcaneal morphological parameters were evaluated.Comparisons were made between postoperative results and preoperative digital design.Results The operating time for the 12 patients ranged from 60 to 90 minutes,averaging 77.9 minutes.Their follow-ups ranged from 4 to 8 months,averaging 6.2 months.No complications affecting their soft tissues happened.The postoperative B(o)hler angle (32.6° ± 3.6°) and Gissane angle (123.9° ± 9.5°) were significantly improved compared with the preoperative values (12.4° ± 2.1° and 143.9° ± 7.8°) (P ＜ 0.001).The shape of postoperative calcaneus was similar to that of the preoperative reduction model.The internal fixation locations and nail directions were in agreement with the preoperative design.Their average Maryland score was 87.8 and excellent to good rate 91.7％.Conclusion This technique can transform a digital design for intra-articular calcanealfracture into real operation tools to help realize a precise surgical design for such fractures.
ABSTRACT
At present, the prevalence rate of diabetes presents a rising tendency. The cardiovascular disease is a major complication of diabetes mellitus and acute coronary syndrome (ACS) is a severe form of coronary heart disease. Compared with non-diabetic patients, the disease situation in diabetic ACS patients is more serious with more contradictory problems and difficulty in treatment. Although percutaneous coronary intervention (PCI) plays a certain role in re-canalization of coronary artery, after PCI the problems the patients with diabetic ACS will face are still serious. traditional Chinese medicine (TCM) recognizes that the etiology and pathogenesis of diabetic ACS are deficiency in Qi and Yin, and accumulation of blood stasis and toxin inside the body. Through clinical observation and retrospective analysis, it is found that using "supplementing Qi and nourishing Yin, activating blood circulation and detoxifying"can interfere with the patients' diabetic ACS and simplify the therapeutic regimen, which is an integrated regulatory treatment with multiple links, multiple pathways and multiple targets, and is a sufficient realization of unique superiority of traditional Chinese medicine by using holistic concept, syndrome differentiation and multiple-link interference for comprehensive prevention and treatment of diabetic ACS.
ABSTRACT
The clinical case report is a popular type of paper for clinicians. Although the evidence level of the case report is not high in evidence-based medicine, it has special value for clinicians. Compared to a lengthy paper, a case report seems simpler; but in fact, it is not easy to write a high-quality case report. To standardize the writing and publication of case report, some international medical groups have developed specific guidelines for case report writing, and the CARE guidelines developed by the CARE group is one of them. In addition, many international leading medical journals also put forward specific requirements on case report writing in introductions for authors. Therefore, this paper introduces the CARE guidelines and 2016 CARE Checklist, and summarizes the writing requirements on case report of some international leading medical journals, in order to provide assistance to improve the domestic authors' skills for writing a case report.
ABSTRACT
OBJECTIVE:To evaluate the economic value of Shenqi fuzheng injection combined with chemotherapy vs. chemo-therapy alone for non-small lung cancer(NSCLC),and to provide reference for drug payment and clinical treatment. METHODS:By prospective cohort design,516 patients with non-small cell lung cancer from 11 hospitals were selected as subjects according to the sale distribution of Shenqi fuzheng injection in district and hospital;267 cases of Shenqi fuzheng injection combined with che-motherapy and 249 cases of chemotherapy alone formed naturally according the clinical therapy plan. The cost-effectiveness and cost-utility analysis were conducted using FACT-L score,KPS score and ZPS score as effect index,QALYs as effectiveness index observation period of 21 d. RESULTS:5 dimensions FACT-L score:the patients of Shenqi fuzheng injection combined with chemo-therapy group could be effectively improved,and the cost-effectiveness ratio was lower than chemotherapy alone group;KPS score:the cost-effectiveness ratio of Shenqi fuzheng injection combined with chemotherapy group was lower than chemotherapy alone group (1 632.44 vs. 11 145.30),and incremental cost-effectiveness ratio was 448.69. ZPS score:Shenqi fuzheng injection combined with chemotherapy group was lower than chemotherapy alone(-17 398.77 vs. 384 513.00). Shenqi fuzheng injection combined with chemotherapy group was lower than chemotherapy alone group in average cost per 1 QALYs(1 313 326 yuan vs. 13 374 365 yuan). CONCLUSIONS:Compared with chemotherapy alone group,Shenqi fuzheng injection combined with chemo-therapy can effectively improve the quality of life,and it is worth of spending more money on Shenqi fuzheng injection from the perspective of the pharmacoeconomics.